- Go on "Prepare" -> "Auto home" (to auto set it)
- Go on "Prepare" -> "Disable steppers" (to be able to move motors X and Y)
- Go on "Prepare" -> "Move axis" -> "Move Z" (to be able to move it up and down 0.001)
- Put a small white paper between the bed and the buse to check if the bue height is good
/!\ Warnings:
- You will have to make the same test on the four corners, then in the middle
- You have to check again the two first corners, after do the four corners (because it can move them when you set the last one)!
- You have to check it again before every print (except if you have the automatical system)!
- The paper has to be able to move but be hook by the buse. Otherwise, you have to use the wheel to adjust it!
-> Post printing advice:
- You can, being careful, use a lighter by passing it quickly over all surfaces, to remove all small filaments and other residues
- You can, using acrylic paint, paint your creations as you wish
You need also a software to create (or import and edit) 3D model and export it to STL file :
- Ultimaker cura: https://ultimaker.com/fr/software/ultimaker-cura
- Autodesk - Tinkercad (online website): https://www.tinkercad.com/things
- Autodesk - Fusion 360: https://www.autodesk.com/products/fusion-360/overview
/!\ Or with soap and water, leaving to dry well!
- Compression springs
- Extruder (metal)
- Motherboard (Marvin 2.0)
- Thingiverse (e.g.: https://www.thingiverse.com/Canan/collections/mods)
- NiTro Nozzle 0.40mm (100% Nickel) https://www.hotends.fr/en/-accessories/52-buse-nitro-020-mm.html
- Allez sur "Prepare" -> "Auto home" (pour le définir automatiquement)
- Allez sur "Prepare" -> "Disable steppers" (pour pouvoir déplacer les moteurs X et Y)
- Allez sur "Prepare" -> "Move axis" -> "Move Z" (pour pouvoir le déplacer de haut en bas 0,001)
- Placez un petit papier blanc entre le lit et le bus pour vérifier si la hauteur de frappe est bonne
/!\ Avertissements :
- Vous devrez faire le même test aux quatre coins, puis au milieu
- Vous devez vérifier à nouveau les deux premiers coins, après les quatre coins (car cela peut les déplacer lorsque vous définissez le dernier) !
- Vous devez le vérifier à nouveau avant chaque impression (sauf si vous avez le système automatique) !
- Le papier doit pouvoir être déplacé mais être accroché par la buse. Sinon, vous devez utiliser la molette pour l'ajuster !
-> Conseils post impression :
- Vous pouvez, en faisant attention, utiliser un briquet en le passant rapidement sur toutes les surfaces, pour supprimer tous les petits filaments et autres résidus
- Vous pouvez, en utilisant de peinture acrylique, peindre à votre guise vos créations
Vous avez également besoin d'un logiciel pour créer (ou importer et éditer) un modèle 3D et l'exporter dans un fichier STL :
- Ultimaker cura : https://ultimaker.com/fr/software/ultimaker-cura
- Autodesk - Tinkercad (site web en ligne) : https://www.tinkercad.com/things
- Autodesk - Fusion 360 : https://www.autodesk.com/products/fusion-360/overview
/!\ Ou avec de l'eau et du savon, en laissant bien sécher !
- Ressorts de compression
- Extruder (métal)
- Carte mère (Marvin 2.0)
- Thingiverse (e.g.: https://www.thingiverse.com/Canan/collections/mods)
- Buse NiTro 0.40mm (100% Nickel) https://www.hotends.fr/en/-accessories/52-buse-nitro-020-mm.html